Skip to main content
PortaPro, home page
Choosing software

Porta potty software vs general field service software

What is actually different

General field service software is built to bill a job. A portable sanitation company bills a unit that sits on a site for months. Here is where that difference shows up, and how to test for it before you buy.

November 5, 20264 min read

Search for porta potty software and the results mix two kinds of product. Some are built for portable sanitation companies. Others are general field service tools, the kind a plumber or a lawn crew uses, with a page that mentions portable toilets. Both have a schedule, a driver app and invoices, so on a feature list they look the same.

They are not the same, and the difference is not a missing feature you can work around. It is what the software thinks a customer is paying for.

A job versus a unit that sits

General field service software is built around the job: someone calls, a tech goes out, the work is done and the job is invoiced. That is how a plumber gets paid.

A portable sanitation company mostly gets paid for something else. A unit is delivered to a construction site and stays there for four months, serviced every week, and the customer pays for it every cycle until it is picked up. The service visits are not what you bill; the unit being there is. Software built for this industry keeps that as a rate card on the site: what is there, how often it is serviced and what it costs per cycle. General software has to fake it with a recurring invoice that someone edits every time a unit is added, swapped or pulled.

Billing a cycle, not a visit

Once the unit is the thing being billed, a handful of rules follow, and each is a place a general tool needs a person:

  • The cycle. Many operators bill every 28 days, not by calendar month. Our post on 28-day versus monthly billing explains why.
  • The first invoice. A unit dropped on day nine of the cycle bills a partial first cycle. Our post on prorating the first invoice walks through the math.
  • One customer, many sites. A builder with units on twelve lots wants one invoice per lot, each with that lot's address and purchase order.
  • The pause and the pickup. A seasonal site stops billing for the winter without being deleted, and a pulled unit stops billing from the day it left.
  • The check. At the end of the cycle, something has to list every unit that should have billed and say whether it did. With a recurring invoice per customer, that check is a person with a spreadsheet.

The schedule comes from the rate card

In a general tool, every service visit is a job someone created, or a recurring job someone set up separately from the invoice. When the customer adds two units, the invoice and the schedule are changed in two places, and the day one of them is missed is the day you service units you are not billing for, or bill for units nobody serviced.

Portable sanitation software reads the service day and frequency from the same rate card the invoice comes from, so adding a unit to a site changes both at once.

Routes around a tank, not a clock

A plumber's route is limited by hours. A pump truck's route is limited by its tank: after a certain number of units it has to go to a disposal site, which keeps its own hours, before it can service the next one. General route optimization does not know the truck has a tank. Our post on route planning around the tank covers what the routing has to know.

Where the unit is, and proof it was serviced

A construction site has one address and units spread over forty acres. The driver needs a pin for each unit, not the street address, and the office needs to know which units are where when the customer calls about one. Then the customer disputes a service, and the answer is a photo with the time and location the driver took it. General tools have photos on jobs; portable sanitation tools tie them to the unit and the stop.

When a general tool is fine

If most of your work is one-off: a weekend event, a single pump-out, a job that is billed once and done, a general field service tool can carry it. The case for industry software grows with the number of units sitting on sites month after month, because that is where the hand-built recurring invoices and the end-of-cycle check pile up.

How to tell on a demo

Bring three real customers: one on a 28-day cycle, one who started mid-cycle and one with units on several sites. Ask the vendor to set them up while you watch and show the first invoice for each, then the report of what should have billed last cycle. A tool built for the trade does it in the demo. A general tool will show you a workaround. Then use our guide on how to compare portable toilet software for price, contract and setup time.

Questions this post answers

Can I run a porta potty business on general field service software?

You can run the schedule on it. The trouble starts with billing: a general tool invoices jobs, so a unit that sits on a site for four months becomes a recurring invoice someone builds and checks by hand, and the first partial cycle, a mid-cycle swap and a seasonal pause are all manual work.

What is the one test that shows the difference?

Ask for the first invoice of a unit placed on day nine of a 28-day cycle, then the invoice for a customer with units on four sites, then the report of every unit that should have billed last cycle and whether it did. Portable sanitation software answers all three on screen.

Is portable sanitation software only for portable toilets?

Most of it covers the whole trade: restrooms, hand-wash stations, restroom trailers, holding tanks and often septic and roll-off work, because the same companies run them from the same yard.

See it on your own book.

Book a walkthrough with your own sites, units and billing cycle, or start a free trial and import your customer list tonight.

Start free trial

14-day free trial (card required, no charge today). Or a guided 30 to 60 day trial with no card.

Kygo, PortaPro's support assistant